In RF & uWave automated test systems, your switching subsystem does far more than route signals. It sits directly in the measurement path, and every relay, connector, cable, and trace between your instrument and the device under test shapes what you actually measure. Choose the wrong switching, and you introduce loss, reflections, and interference that corrupt results before your analyzer sees them. Choose the right switching, and you protect signal integrity, accuracy, and repeatability across thousands of test cycles.
Simon Aylott, head of Pickering’s microwave business unit, recently contributed a technical article on Everything RF that examines this relationship in detail, explaining why switching decisions carry so much weight in RF test and what to look for when specifying a solution.
Here's what you'll take away from the piece:
- Ways switching affects RF signal integrity end-to-end
- Which relay technologies suit different frequency and power ranges
- How insertion loss, isolation, and crosstalk drive measurement accuracy
What the Article Covers
RF signals are unforgiving. At higher frequencies, small imperfections in the signal path produce measurable errors, making the switching subsystem a core part of your measurement uncertainty budget, rather than a passive interconnect. The article breaks down the technical factors that separate a switching solution that preserves your signal from one that quietly degrades it.
RF Signal Integrity
Maintaining signal integrity means preserving the amplitude, phase, and shape of your RF signal as it travels from instrument to device, and depending on the test being performed, on the return journey. Impedance matching (typically 50 ohms in RF systems) is critical, as any mismatch creates reflections that appear as measurement errors. Our article explains how controlled impedance, careful signal path design, and proper termination keep your signals clean across the frequency range you're testing.
Relay Selection for RF Applications
Relay choice sets the performance ceiling for your switching. Different technologies serve different needs:
- Coaxial electromechanical relays handle higher power and offer excellent RF performance up to 110 GHz.
- Reed relays switch fast, provide long mechanical life, and suit high-density configurations up to 250 MHz RF testing.
- Solid-state RF relays support up to 8 GHz frequencies with very long life and fast switching. Lack of a DC path and high insertion loss can limit suitable applications.
- MEMS RF relays enable long operational life (up to 3 billion operations) and offer low insertion loss compared to solid-state devices.
Matching the relay to your frequency, power level, and switching-life requirements avoids over-specifying, while ensuring the signal path meets your application’s demands.
Insertion Loss, Isolation, and Crosstalk
These three parameters define RF switching performance:
- Insertion loss is the signal power lost as it passes through the switch path. Excess loss reduces dynamic range and can mask low-level signals.
- Isolation measures how well an open path blocks a signal, keeping signals contained to their intended path when routing high- and low-level signals near each other.
- Crosstalk is unwanted coupling between adjacent paths. In dense, high-channel-count systems, poor crosstalk performance corrupts measurements on neighboring channels.
Each parameter degrades with frequency, so a switch that performs well at 1 GHz may fall short at 6 GHz. The article stresses reading datasheets against your actual test frequency, rather than a nominal figure.
Impact on Test Accuracy and Repeatability
Signal integrity, relay selection, and RF parameters converge on the two outcomes engineers care about most: accuracy and repeatability. A well-specified switching solution delivers consistent path characteristics, measurement after measurement, so the results reflect the device under test rather than variation in the switching. Modular PXI and LXI platforms support this by combining characterized RF performance with the density and scalability real test systems need.
Key Takeaways for Test Engineers
- Switching is part of your measurement path, not a passive connection. Its performance directly affects every RF measurement.
- Impedance matching protects signal integrity. Mismatches create reflections that add error across your frequency range.
- Match the relay to the application. Frequency, power, acceptable performance, and switching life determine which RF relays are the best fit.
- Watch insertion loss, isolation, and crosstalk together. These parameters define RF performance and worsen as frequency rises.
- Verify performance at your test frequency. Datasheet figures at low frequencies can mislead you at higher bands.
- Repeatability depends on consistent path characteristics. The right switching keeps results stable across thousands of automated cycles.
- Modular PXI and LXI platforms deliver characterized RF performance with the density and scalability production systems require.
The switching you choose sets the limits on what your RF test system can measure. Get it right, and you build accuracy and repeatability into the foundation of your test program.
The complete article goes deeper into RF switching performance, relay technologies, and design practices that keep RF measurements accurate and repeatable. If you're specifying or upgrading an RF test system, it's a worthwhile read for sharpening your approach.
